ATTO FibreCenter™ 3400R/DInstallation and Operation Manual© 2002 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks
5 ATTO FibreCenter 3400 Installation and Operation Manual3 ATTO FibreCenter installation optionsThe ATTO FibreCenter 3400R/D provides a 2-gigabit Fibr
Managed Data Path Model 6hub is 192.168.1.1. You can use a crossover Ethernet cable to direct connect a PC to the FibreCenter 3400D or a standard Et
7 ATTO FibreCenter 3400 Installation and Operation Manual3.1 Setting up the Fibre Channel Rack SystemThe ATTO Fibre Channel Rack System is a configura
Managed Data Path Model 8Output voltage:+12 Volts @ 5 Amps (60 watts) continuous, 5.8 amps (70 watts) peak.Power draw: The maximum power draw is 2 A
9 ATTO FibreCenter 3400 Installation and Operation Manual3.2 Installing the ATTO FibreCenter 3400RThe ATTO FibreCenter 3400R fits into a standard rack
Managed Data Path Model 10Cabling Fibre Channel portsThe FibreCenter 3400R uses a Small Formfactor Pluggable (SFP) Fibre Channel interface. The type
11 ATTO FibreCenter 3400 Installation and Operation Manual3.3 Installing the ATTO FibreCenter 3400DThe ATTO FibreCenter 3400D is a stand alone desktop
Managed Data Path Model 12Cabling Fibre Channel portsThe FibreCenter 3400D uses a Small Formfactor Pluggable (SFP) Fibre Channel interface. The type
13 ATTO FibreCenter 3400 Installation and Operation Manual3.4 Configuring the ATTO FibreCenterThe ATTO FibreCenter 3400R/D may be configured into 48 c
Managed Data Path Model 14the last mapping designated by the Set zone and Commit Zone commands.Example: set up one zone1 At the Command Line Interfa
15 ATTO FibreCenter 3400 Installation and Operation Manual4 Command Line Interface use and guidanceYou will be able to perform all configuration via t
Managed Data Path Model 16Exhibit 4-5 Command conventions. Do not type symbols when entering commands.Symbol Indicates[ ] Required entry< &g
17 ATTO FibreCenter 3400 Installation and Operation Manual 4.1 General use commandsSeveral commands may be invoked at any time. Commit ZoneCommit all
Managed Data Path Model 18 4.2 Ethernet and Telnet configuration commandsConfigure the ATTO FibreCenter 3400R/D using a telnet session over the Ethe
19 ATTO FibreCenter 3400 Installation and Operation Manual 4.3 Configuration commandsConfigure the ATTO FibreCenter 3400R/D using a telnet session ove
Managed Data Path Model 20Zone RestoreSets the new parameters for each port in the zonelist to the current settingActions: set Zone RestoreInformati
21 ATTO FibreCenter 3400 Installation and Operation Manual 4.4 Diagnostic commandsThe commands in this section only provide information about the ATTO
Managed Data Path Model 225 TroubleshootingThe fault LED indicates that a signal is being received, but the signal contains enough faults to make th
23 ATTO FibreCenter 3400 Installation and Operation Manual6 Updating firmwareThe Linux Kernel and the Flash File System may be updated by accessing th
iIndex: Command Line InterfaceA summary of the Command Line Interface commands, their defaults, an example of how they might be used, and where you ca
ii ATTO FibreCenter 3400 Installation and Operation ManualAppendix A Standards and compliancesThe ATTO Technology FibreCenter 3400R/D described in thi
Managed Data Path Model iiiAppendix B Contact ATTO Technology, Inc. Customer service, sales information and technical support are available by phone
Contents1 Fibre Channel is a key technology for storage ...1Glossary2 ATTO FibreCenter 3400R/D characteristics ...
4.2 Ethernet and Telnet configuration commands ...18Default RouterEchoFactory DefaultsIdle TimeoutIP AddressSecurity TrapsSubnet Mask4
1 ATTO FibreCenter 3400 Installation and Operation Manual1 Fibre Channel is a key technology for storageFibre Channel is a serial communications techn
Managed Data Path Model 2LED Light-emitting diode, a type of diode that emits light when current passes through it. Visible LEDs are used as indicat
3 ATTO FibreCenter 3400 Installation and Operation Manual2 ATTO FibreCenter 3400R/D characteristicsThe ATTO FibreCenter 3400R/D is a 2-Gigabit Fibre C
Managed Data Path Model 4Rack System provides a maximum port density of 16 SFP ports and redundant power and cooling in a full width 1U rack.The ATT
Komentáře k této Příručce